BullMach BM-66 LWE - Petrol Snowplough - Loncin G210F(D)S

The BullMach BM-66 LWE petrol snow blower is a product suitable for intense work on medium-sized areas, where sealing and adherence to the ground are essential for a good result.

Other machine features include:

• LED light
• Mechanical gearbox with 6+2 gears
• Clean-out tool for unclogging

Powered by a 212 cc Loncin G210F(D)S engine. It features a motor with a nominal capacity of 7 HP It is a heavy-duty product equipped with a large 66 x 51 cm front auger with optimized profile steel spiral and serrated edge.

The electric starting of the snow blower is possible via the domestic current, allowing the machine to be switched on even at very low temperatures. The auger shreds the snow and expels it many meters away through the discharge chute that is tilting and adjustable.

The snow blower is equipped with a 212cc 4-stroke air-cooled Loncin G210F(D)S engine, with over head valves and aluminium cylinder.

Features:

The engine of this snow blower is also equipped with electric starting. This machine is equipped with battery. In fact, it allows you to start the snow blower directly from the available electrical socket. This solution was devised as batteries, subjected to sudden changes in temperature, tend not to hold a charge.

Focus on the engine oil cap

Focus on the ignition keys

WARNING
The engine is PROVIDED WITHOUT OIL.
Make sure to carefully read the instruction manual before starting the unit.

Nominal Power: 7 HP The correct term would be "Commercial” Power, meaning the classic standard of definition of power officially used until a few years ago by all leading engine manufacturers.

* This figure is even more widespread and advertised in the leading commercial channels, although it is higher than the actual power.

Effective power: 5.9 HP (rotation speed: 3600 rpm)
It corresponds to the real power expressed by the crankshaft. This is the power indicated as official in the manual or in the technical data of the motor manufacturer.

* This technical data may vary for the same engine model depending on the rotational speed supplied by the engine applied to the equipment.

The discharge chute of this snow blower is made of enamelled steel and adjustable through the knob placed on the side of the handlebar.

The rotation angle of the chute is 190°: the snow blower chute rotates through 95° to either side of the direction of travel

Focus on the discharge chute completely oriented to the left

Focus on the discharge chute completely oriented to the right

Deflector placed completely at the top, to obtain maximum ejection distance.

Deflector placed completely at the bottom .

The discharge chute is also equipped with an anti-intrusion safety grid.

The auger compartment is 66cm wide and 51cm high.

The auger supplied with the snow blower is heavy-duty with steel spiral with an optimized profile and serrated edge. These features make it suitable to shred even the hardest snow.

The safety bolts protect the integrity of the gear reducer. They are in fact specifically designed to fail when the blade gets stuck against some stone or obstacle.

Two-stage

The snow is efficiently collected inside the machine through the auger, which expels it through the discharge chute via a high-speed internal centrifugal fan equipped with reinforcement bars.

Aluminium angle reducer with internal grease-bath steel gears.

Adjustable plastic side slides
They allow this snow blower to work on all types of terrain, from the smoothest to those not perfectly even (raising the working height through the slides). It can also work on gravel surfaces.
The plastic structure allows you to work even on particular grounds without scratching them.

The control panel of this snow blower is simple, intuitive and very functional.

Gear lever on the right: 6 forward speeds 2 reverse speeds

Focus on the switch for switching on the led headlight

Lever on the top of the right handle: activates and deactivates the operation, (whatever the speed selected on the automatic transmission, forward or reverse). By releasing this lever, the machine stops instantly, for safety reasons.

Lever at the top of the left handle: activates and deactivates both the auger and the high-speed fan (activates and deactivates both simultaneously).

Discharge chute adjustment: adjustable through the knob

Powerful and precise lighting thanks to the led lamps placed in front of the control panel.

Tool for unclogging.
If the discharge chute clogs, you can easily use this tool to unclog it.

Traktor wheels which guarantee great adherence to the ground, making the most of the engine power.

The dimensions are 14x4.10-6